. Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not be obstructed.

1. Nieco Mpb94 Broiler
2. Nieco Mpb94 Broiler Service Manual

Operating personnel must not perform any maintenance or repair functions. Contact your Nieco Authorized Dealer. IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. Warranty Information.34 Nieco Corporation - Model MPB94. IMPORTANT The Nieco Corporation reserves the right to change specifications and product design in accordance with the general terms and conditions outlined in the BURGER KING®/Vendor agreement. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Nieco and the Burger King Corporation have worked together to cre- ate a set of standards for broiler performance, food quality and food safety. The use of non-Nieco parts is capable of affecting these criteria, and may affect broiler performance, parts longevity and food safety. Your local Authorized Nieco Distributor and Service Agent has been factory trained and has a complete supply of parts for your Nieco Automatic Broiler. Distributor for adjustment or repair. Use only genuine Nieco replacement parts for your broiler. Failure to do so will void the warranty and may significantly alter the performance of your broiler.

Nieco and the Burger King Corporation have worked together to create a set of standards for broiler performance, food quality and food safety. Do not obstruct the flow of combustion and ventilation air. An adequate air supply must be available for safe and proper operation. For installations in the Commonwealth of Massachusetts the following shall apply: Venting shall be in compliance with NFPA Section 10.3.5.2 for the Model MPB94.

B.5 Clearance Keep appliance area free from combustibles. For easy movement of the appliance, the connector should be installed with a 'lazy' loop for minimum tension. Note: Gas appliances should be disconnected prior to maximum movement. (Minimal movement is possible to connect hose.) Nieco Corporation - Model MPB94. Note: Disconnect power before servicing. B.10 Pre-Operation Check Be sure that all parts are installed in the proper location: J Ventilation is turned on J Broiler is plugged in J Gas line is connected Nieco Corporation - Model MPB94.

On/Off Indicator Light P/N 4100 Main On/Off Switch P/N 15480 ON DISCHARGE END BEHIND BOTH CONTROL BOXES Gas Gauge Belt Reverse Buttons - Push to reverse the P/N 16036 belts in case of a jam. Nieco Corporation - Model MPB94. (2) PRODUCT SELECTION BUTTONS - Press to select different presets for different products. (3) ADJUSTMENT KNOB - Use to adjust product cook times, element settings and product names. (4) SELECTION INDICATOR LIGHT - Lights up to show which button is selected. Nieco Corporation - Model MPB94. NORMAL IGNITION The MPB94 is equipped with automatic ignition.

When the broiler is turned on, a hot surface ignitor turns on 5 seconds before the flow of gas. Gas then flows to all of the burners. If the burners are not lit within 10 seconds, the control will reset and try again for 10 seconds. Your Nieco Automatic Broiler is designed to automatically stop gas flow to the broiler in the event of power failure, gas pressure loss or any other related incident. No attempt to operate this appliance should be made in the event of a power failure. Press and turn the knob until the set point temperature reads the same as the actual temperature (See C).

Your broiler is now calibrated. NOTE: The temperatures shown here are for illustration purposes only. Your broiler temperatures will be different. Nieco Corporation - Model MPB94. Press the product selec- tion button twice (2X) to get to the burner selection screen. Turn the knob to YES or NO.

When you are done making changes, the control will automatically save your changes after 5 seconds. Nieco Corporation - Model MPB94. (10 character limit). Press and hold the PRODUCT SELECTION BUT- TON for 5 seconds to save the changes and return to normal operation. C.4.12 Factory Presets The MPB94 uses the following factory presets for the Multi-Product Control: Product Product Name Cook Time.

How to remove and Instructions clean the parts. Pull each meat guide out slightly from the bottom, then lift off. Wash, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model MPB94 Nieco Corporation - Model MPB94. Meat Guides Clean: Every 4 hours Feed End Tools Scrub Pad 3-Compartment Sink Instructions Pull each meat guide out slightly from the bottom, then lift off.

Wash, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model MPB94. Wash, rinse, and sanitize in the 3-compartment sink. DO NOT lift the feeder base by the feeder bar or the chains.

This will damage the feeder base. REASSEMBLY: Pull the release pin and place feeder base in position. Nieco Corporation - Model MPB94. Make sure grease pan is cool before putting in water or it may warp the pans. Take to sink area and spray with degreaser.

Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model MPB94. Feed End Tools Soapy Towel Sanitized Towel Instructions Clean product holding area while still warm.

Wring out a soapy towel and wash product holding area. Wring out a sanitized towel and wipe product holding area. Nieco Corporation - Model MPB94. Tilt and lift pins off hooks; lift off.

Take to sink area and spray with degreaser. Wash, rinse, and sanitize in the 3-compartment sink. REASSEMBLY: Make sure pan inserts are on and return pan hangs on brackets. Nieco Corporation - Model MPB94. Scrape each shaft of both belts on the discharge end with the wide end of the shaft cleaning tool. The tool is located on the clip on main side control box. Wipe shaft cleaning tool with a towel.

Nieco Corporation - Model MPB94. 3-Compartment Sink Instructions Lift grease box off. Take to sink area and spray with degreaser.

Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. REASSEMBLY: Put grease box on before the grease trough. Nieco Corporation - Model MPB94. If necessary, use a stiff toothbrush to clean any clogged burner holes. Repeat steps for all burners. REASSEMBLY: Be sure the holes on the burner are facing up. Burners must be completely dry before reassembly.

Nieco Corporation - Model MPB94. REASSEMBLY: Make sure shields are seated properly on brackets. Flame Sensor Clean: Weekly Feed End Tools Scrub Pad Flame Sensor Instructions Polish with a dry scrub pad. Do NOT use water on the flame sensor. No spray No water Nieco Corporation - Model MPB94.

EXTREMELY HOT! Be careful not to burn yourself. Lift cap from shroud collar. Take to sink area and spray with degreaser.

Wash with a scrub pad, rinse, and sanitize in the CAUTION: 3-compartment sink. Extremely Hot Nieco Corporation - Model MPB94. If necessary, use a stiff toothbrush to clean any clogged burner holes.

Repeat steps for all burners. Burners must be completely dry before reassembly. Orifices Clean: Monthly Inside Tools Small Orifice Brush Burner Orifice Instructions Clean orifices using a small, dry orifice brush. Nieco Corporation - Model MPB94. Flex side: adjust conveyor speed, duty cycle, and burner settings. Clean burners and orifices.

Excessive flaming in broiler. Clean or rotate the flame arrestors, Clean the catalyst if equipped. Check the hood for proper operation. Check product for overcooking. Nieco Corporation - Model MPB94. PARTS LOCATION DRAWINGS MPB94 Feed End View Nieco Corporation - Model MPB94. PARTS LOCATION DRAWINGS MPB94 Discharge End View Nieco Corporation - Model MPB94.

WIRING DIAGRAM - Main Side Nieco Corporation - Model MPB94. WIRING DIAGRAM - Flex Side Nieco Corporation - Model MPB94. 29.15 codes. 24.58 CAUTION Do not operate the broiler at gas pressures other than those stated here. Doing so will affect the opera- tion of your broiler. Nieco Corporation - Model MPB94. Generally, your guarantee provides replacement of all parts, which fail due to defects in manufacture for one year after startup of the machine.

Parts which fail will be replaced by the Nieco distributor or Service Center in your area who did the startup service. If the part is a customer installed component, the part will be sent you to replace the defective part on your machine. This is particularly true of high value important components as motors and controls, or any parts showing a pattern of failure.

Nieco Mpb94 Broiler

If required, Nieco will pay the return freight cost and give instructions via your servicer on how to return the parts. Nieco Corporation 7950 Cameron Drive Windsor, CA 95492 (707) 284-7100 Office.

(707) 284-7430 Fax www.nieco.com. e-mail: service@nieco.com Printed in the USA © 2005 Nieco Corporation Reorder # 9999-99203.

Nieco Mpb94 Broiler Service Manual

6/06.