. SFC 18­A SFC 22­A English Printed: Doc-Nr: PUB / 5293242 / 000 / 00. Printed: Doc-Nr: PUB / 5293242 / 000 / 00.

1. Manual Hilti 2016 Pdf

Manual Hilti 2016 Pdf

Direct current (DC) 1.3 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed. ▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. ▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Service ▶ Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2.2 Additional safety precautions for screwdrivers Personal safety ▶ Only use the product if it is in perfect working order. Printed: Doc-Nr: PUB / 5293242 / 000 / 00. Printed: Doc-Nr: PUB / 5293242 / 000 / 00. 3 Description 3.1 Overview Printed: Doc-Nr: PUB / 5293242 / 000 / 00.

The product described is a hand-held cordless drill / driver. It is designed to be used for driving and removing screws and for drilling in steel, wood and plastic. ▶ Use this product only with Hilti Li­ion batteries of the B18 / B22 series. ▶ Use only the Hilti battery chargers of the C4/36 series for these batteries. 5 Operation 5.1 Inserting the battery CAUTION Risk of injury. The drill/driver may start inadvertently. ▶ Before fitting the battery, check that the drill/driver is switched off and that the switch safety lock is activated.

CAUTION Electrical hazard. Dirty contacts may cause a short circuit.

5.3 Fitting the accessory tool 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. Check that the connection end of the accessory tool is clean. Clean the connection end if necessary. ▶ Fit the belt hook.

6 Troubleshooting 6.1 Troubleshooting If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service. Trouble or fault Possible cause Action to be taken The power tool does not The battery is not fully inserted. Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling.

Ask Hilti Service or your Hilti representative for further information. Printed: Doc-Nr: PUB / 5293242 / 000 / 00. Printed: Doc-Nr: PUB / 5293242 / 000 / 00.

Hilti = registered trademark of Hilti Corp., Schaan 20160714 Printed: Doc-Nr: PUB / 5293242 / 000 / 00.

. SID 4-A22 English Printed: Doc-Nr: PUB / 5293904 / 000 / 00. Printed: Doc-Nr: PUB / 5293904 / 000 / 00. Direct current (DC) 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel.

This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed. The type designation and serial number are printed on the type identification plate. ▶ Write down the serial number in the table below.

You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information. ▶ Remove the battery from the power tool before making any adjustments, changing accessories or storing the tool. This precaution reduces the risk of the power tool starting accidentally. ▶ Store power tools out of reach of children when not in use. Do not allow persons who are not familiar with the tool or these instructions to operate it. ▶ If the battery is too hot to touch, it may be defective.

In this case, place the power tool in a non-flammable location, well away from flammable materials, where it can be kept under observation and left to cool down. Contact Hilti Service after the battery has cooled down. John deere 530 baler service manual. Printed: Doc-Nr: PUB / 5293904 / 000 / 00. Printed: Doc-Nr: PUB / 5293904 / 000 / 00. Printed: Doc-Nr: PUB / 5293904 / 000 / 00.

3 Description 3.1 Overview of the product Printed: Doc-Nr: PUB / 5293904 / 000 / 00. 3.4 Items supplied Impact screwdriver, operating instructions. Note You can find other system products approved for use with your product at your local Hilti Center or online at: www.hilti.com. 4 Technical data 4.1 Impact wrench Rated voltage 21.6 V. The data given represents the main applications of the electric tool. However, if the electric tool is used for different applications, with different accessory tools, or is poorly maintained, the data may vary. This may significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the power tool is switched off, or when it is running but not actually being used for a job. ▶ Fit the battery and make sure that it is heard to engage. 5.2 Fitting the belt hook (optional) WARNING Risk of injury! Hazard presented by a falling power tool. ▶ A falling power tool may present a risk of injury to yourself and others.

Check that the belt hook is fitted securely before beginning work. 5.3 Fitting an accessory tool 1.

Check that the connection end of the accessory tool is clean. Result The connection end is dirty. ▶ Clean the connection end. Set the forward/reverse switch to the middle position or remove the battery from the power tool.

5.5 Setting the torque ▶ Push the torque selector button repeatedly until the desired torque setting is displayed in the torque display. 5.6 Setting forward or reverse rotation Note An interlock prevents switching while the motor is running. The control switch is locked when the forward/reverse switch is in the middle position (safety lock). To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com ▶. Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled.

In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. Printed: Doc-Nr: PUB / 5293904 / 000 / 00. Hilti = registered trademark of Hilti Corp., Schaan 20160728 Printed: Doc-Nr: PUB / 5293904 / 000 / 00.